System-sensor B110LP Manuel d'utilisateur télécharger pdf

D150-05-00 1 I56-594-03R

B110LP Plug-in Detector Base

For use with the following smoke detectors:

IN US: 1151, 2151

IN CANADA: 1151A, 2151A

IN EUROPE: 1151E, 2151E

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

Before Installing

Please thoroughly read the System Sensor manual I56-407,

Guide for Proper Use of System Smoke Detectors, which pro-

vides detailed information on detector spacing, placement,

zoning, wiring, and special applications. Copies of this

manual are available at no charge from System Sensor. (For

installation in Canada, please refer to CAN/ULC-S524,

Standard for the Installation of Fire Alarm Systems and CEC

Part 1, Sec. 32.)

NOTICE: This manual should be left with the owner/user

of this equipment.

IMPORTANT: The detector used with this base must be

tested and maintained regularly following NFPA 72 require-

ments. The detector used with this base should be cleaned

at least once a year.

Specifications

Base Diameter: 6.2 inches (157 mm)

Base Height: 0.95 inches (24 mm)

Weight: 0.3 lb. (137 g)

Mounting: 4-inch square box with or without plaster ring. Min. depth–1.5 inches

3-1/2-inch octagon box. Min. depth–1.5 inches

Operating Temperature Range: 0° to 49°C (32° to 120°F)

Operating Humidity Range: 10% to 93% Relative Humidity, Noncondensing

Electrical Ratings - includes base and detector

System Voltage: 12/24 VDC

Maximum Ripple Voltage: 4 Volts peak-to-peak

Start-up Capacitance: 0.02 µF Maximum

Standby Ratings: 8.5 VDC Minimum

35 VDC Maximum

120 µA Maximum

Alarm Ratings: 4.2 VDC Minimum at 10 mA

6.6 VDC Maximum at 100 mA

(Alarm current must be limited to 100 mA (130 mA for models 1151 and 2151) by the

control panel. If it is used, the RA400Z Remote Annunciator operates within the specified

detector alarm currents.)

Reset Voltage: 2.5 VDC Minimum

Reset Time: 0.3 Seconds Minimum

Start-up Time: 34.0 Seconds Maximum

General Description

The Model B110LP detector base is designed for use with

System Sensor models 2151 photoelectronic and 1151 ion-

ization detector heads. This two-wire base is equipped with

screw terminals for the connection of power, ground, and

an optional remote annunciator.

Mounting

The detector base mounts directly to 3-1/2 inch and 4-inch

octagon boxes and 4-inch square boxes, with or without

plaster rings. To mount the base, remove the decorative

ring by rotating it in either direction to unhook the snaps

before separating the ring from the base. Use the screws

supplied with the junction box to attach the base to the box

through the appropriate slots in the base (see Figure 1).

Position the decorative ring around the base and rotate it in

either direction until the ring snaps into place.

1 2 3 4

Résumé du contenu

Page 1 - B110LP Plug-in Detector Base

D150-05-00 1 I56-594-03RB110LP Plug-in Detector BaseFor use with the following smoke detectors:IN US: 1151, 2151IN CANADA: 1151A, 2151AIN EUROPE: 1151

Page 2 - D150-05-00 2 I56-594-03R

D150-05-00 2 I56-594-03RInstallation GuidelinesAllowable loop resistance is an important specification forcontrol panels as well as for smoke detector

Page 3 - D150-05-00 3 I56-594-03R

D150-05-00 3 I56-594-03RNOTE: IF A REMOTE ANNUN-CIATOR IS NOT USED,POLARITY OF THESETERMINALS MAY BEREVERSED.2341REMOTEANNUNCIATOR2341REMOTEANNUNCIATO

Page 4

Commentaires sur ces manuels

Pas de commentaire

System-sensor B110LP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement System-sensor B110LP. System Sensor B110LP User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement System-sensor B110LP