System-sensor KBS and KMS Models Manuel d'utilisateur télécharger pdf

D770-06-00 1 I56-373-03

System Sensor, 3825 Ohio Avenue, St. Charles, Illinois 60174, 1-800-SENSOR2, FAX: 708-377-6495

KMS & KBS BELL SERIES

INSTALLATION INSTRUCTIONS

IMPORTANT

Please Read Carefully and Save

This instruction manual contains important information about the installation and operation of bells. Purchasers who

install bells for use by others must leave this manual or a copy of it with the user.

System Sensor supplies bells for nearly all sprinkler/fire alarm/burglar applications.

These instructions apply to all System Sensor bells in the series. Read all instructions carefully before beginning. Follow

only those instructions that apply to the model you are installing.

CAUTION

DO NOT USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES.

DO NOT LEAVE ANY UNUSED WIRES EXPOSED.

GENERAL DESCRIPTION

The National Fire Protection Association has published codes, standards, and recommended practices for the installa-

tion and use of the above appliances. It is recommended that the installer be familiar with these requirements, with local

codes, and any special requirements of the authority having jurisdiction.

These bells are intended to be connected to alarm indicating circuits of UL listed fire alarm control panels. Terminal con-

nections are polarized to enable supervision of the installation wiring. The KMS bells require 24 VDC and the KBS bells

require 120 VAC.

Before installing any alarm device, be thoroughly familiar with:

NFPA 72: Installation, Maintenance, and Use of Protective Signaling Systems

NFPA 13: Installation of Sprinkler Systems

NFPA 13A: Inspection, Testing, and Maintenance of Sprinkler Systems, specifically Chapters 4 and 5

Other applicable NFPA standards, local codes, and the requirements of the authority having jurisdiction.

Failure to follow these directions may result in failure of the device to report an alarm condition. System Sensor is not

responsible for devices that have been improperly installed, tested, or maintained.

INSTALLATION

WARNING

High voltage. Electrocution Hazard. Do not handle live AC wiring or work on a device to which AC power is applied.

Doing so may result in severe injury or death.

CAUTION: Do not loop wire under terminals. Break wire runs to provide supervision of connections.

1. Remove the gong.

2. Wire the bell in the circuit. See Figure 1. (Note polarity markings on bells.)

NOTE: Terminals on bells are designed to accept 14 GA wire. When using a 10 or 12 GA wire use Panduit terminal

PV106LF or equivalent for connection of power leads.

1 2 3 4

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

D770-06-00 1 I56-373-03System Sensor, 3825 Ohio Avenue, St. Charles, Illinois 60174, 1-800-SENSOR2, FAX: 708-377-6495KMS & KBS BELL SERIESINSTALLA

Page 2 - KMS BELL KMS BELL

3. Mount bell mechanism on 4″ square electrical box with the striker facing down. See Figures 2 – 5.4. Replace the gong.5. The top of the bell must be

Page 3

AUDIBILITY RATING (dBA at 10 ft)UL Spherical Sound MeasurementSound level measurements are made in accordance with UL Standard 464. The sound power ou

Page 4

LIMITATIONS OF ALARM DEVICESSystem Sensor bells are designed to provide fire and security hazard warning.1. Bells may not work or operate properly if

Commentaires sur ces manuels

Pas de commentaire

System-sensor KBS and KMS Models Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement System-sensor KBS and KMS Models. System Sensor KBS and KMS Models User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement System-sensor KBS and KMS Models