System-sensor BEAM200 and BEAM200S Manuel d'utilisateur télécharger pdf (Page 5)

FIGURE 6. WIRING CONNECTIONS AT DETECTOR:

SLC (–)

SLC (+)

SLC (–)

SLC (+)

RESET I NPUT

TEST INPUT

AUX (–)

REMOTE ALARM OUT

NOT USED

REMOTE TROUBLE OUT

TEST OPTION (–)

TEST OPTION (+)

T3 T2 T1

C0260-01

FIGURE 7. WIRING DIAGRAM:

+–

TO NEX

DEVICE

FROM

PANEL OR

DEVICE

LISTED

REMOTE

POWER

SOURCE

ONLY USED FOR

BEAM200S. SEE

ELECTRICAL

RATINGS.

COMMUNICATION LINE

32 VDC MAX.

TWISTED PAIR IS

RECOMMENDED.

–

T3 T2 T1

C0261-00

FIGURE 8. WIRING DIAGRAM (RTS451 OR RTS151):

RTS451/KEY

or RTS151/KEY

DETECTOR

PIN 1

REMOTE ALARM OUT

T2-1

T2-2

T2-4

T2-3

AUX (–)

SLC IN +T1-1

T1-2

T1-3

T1-4SLC IN –

SLC OUT +

SLC OUT –

RESET INPUT

TEST INPUT

T3-3

REMOTE TROUBLE OUTPUT

OPTIONAL YELLOW LED

PIN 2

PIN 4

PIN 3

PIN 5

C0328-03

FIGURE 9. WIRING DIAGRAM (RTS451 OR RTS151):

BEAM200/S

ALARM

SIGNAL

CIRCUIT

(NOTE 1)

T2-1

T2-2

NOTE 1: SEE ELECTRICAL RATINGS SECTION OF

THIS MANUAL FOR CIRCUIT OUTPUT RATINGS.

SLC (+)

SLC (–)

RED

C0320-00

INSTALLATION / ALIGNMENT

Reference Figures 10 through 14 for installation, alignment, and maintenance.

The alignment of the BEAM200/BEAM200S is divided into four steps: coarse

alignment, fine adjustment, final gain adjustment, and final verification. It is

necessary for all four steps to be executed properly to ensure proper alignment

of the product. If the detector and reflector are mounted per Mounting Loca-

tions and Mounting Instructions sections of this manual and the alignment

procedures are executed properly, false alarms and nuisance trouble signals

will be minimized.

PRE-ALIGNMENT CHECKLIST

Ensure that both the detector and reflector are mounted securely to •

stable surfaces.

Ensure that all wiring is correct.•

Ensure that terminal blocks are fully seated into their receptacles on •

the detector.

Complete any wiring dressing to minimize movement to the detector •

once the alignment procedure is completed.

Ensure that the appropriate number of reflectors are used for the in-•

stalled distance. Distances between 230 & 328 Feet (70 - 100m) require

additional reflectors (4 total). The BEAMLRK accessory should be used

in these cases.

Ensure that the line of sight between the detector and reflector is clear •

and that reflective objects are not too near. See Mounting Instructions

for more details.

Ensure that both the detector and reflector are mounted within their •

operational parameters for off axis angles. See Mounting Instructions

for more details.

Disable the zone or system to prevent unwanted alarms before applying •

power.

Ensure power to the detector is “ON”.•

Ensure that the appropriate address is set on the code wheels.•

You are now ready to begin the alignment procedure.

D400-74-00 5 I56-2289-005R

1 2 3 4 5 6 7 8 9 10 ... 14 15

Commentaires sur ces manuels

Pas de commentaire

System-sensor BEAM200 and BEAM200S Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement System-sensor BEAM200 and BEAM200S